Konica i series error codes
Konica Bizhub C450i C550i C650i and Bizhub C250i C300i C360i:
Trouble resetting procedure by Trouble Reset key:
Use
• To be used when the status would not be cleared by turning main power switch OFF and ON again, or opening and closing the front door
or lower front door in case of a trouble.
Procedure
1. Turn OFF the main power switch.
2. Remove the key cover [1] on the rear side of the control panel, and turn main power switch ON while pressing the Reset key [2].
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
6. When the machine fails to start even after perform step 1 through 5, turn OFF the main power switch and unplug the power cord.
7. Insert the power cord after 15 sec. or more, turn ON the main power switch and check if the machine starts correctly.
List of the trouble codes
C0002 Paper feed communication error (When PC-116, PC-216, PC-416, or PC-417 is installed)
C0104 Tray 3/4 feeder transportation motor failure to turn (When PC-417 is installed)
C0105 Tray 3/4 feeder transportation motor turning at abnormal timing (When PC-417 is installed)
C0106 Tray 3 paper feed motor turning at abnormal timing (When PC-116 orPC-216 is installed)
C0107 Tray 3 vertical transport motor turning at abnormal timing (When PC-116 or PC-216 is installed)
C0108 Tray 4 paper feed motor turning at abnormal timing (When PC-216 is installed)
C0109 Tray 4 vertical transport motor turning at abnormal timing (When PC-216 is installed)
C0202 Tray 1 feeder up/down abnormality
C0204 Tray 2 feeder up/down abnormality
C0206 Tray 3 feeder up/down abnormality (When PC-116, PC-216, or PC-417 is installed)
C0208 Tray 4 feeder up/down abnormality (When PC-216 or PC-417 is installed)
C0210 Transfer LCT lift failure (When PC-416 is installed)
C0211 Manual feed up/down abnormality
C0214 Transfer LCT shift failure (When PC-416 is installed)
C0216 External LCT up/down abnormality (When LU-207 or LU-302 is installed)
C1003 PK communication error (Finisher detection) (When FS-540+PK-526 orFS-540SD+PK-526 is installed)
C1004 Finisher communication error (Engine detection) (When FS-533, FS-539, FS-540, or JS-508 is installed)
C1007 PI communication error (Finisher detection) (When FS-540+PI-507 orFS-540SD+PI-507 is installed)
C1013 PK communication error (PK detection) (When FS-540+PK-526 orFS-540SD+PK-526 is installed)
C1014 Finisher communication error (Finisher detection) (When FS-533, FS-539, FS-540, or JS-508 is installed)
C1017 PI communication error (PI detection) (When FS-540+PI-507 or FS-540SD+PI-507 is installed)
C1081 SD communication error (Finisher detection) (When FS-539SD orFS-540SD is installed)
C1082 SD communication error (SD detection) (When FS-539SD or FS-540SD is installed)
C1102 Tray lift up motor drive malfunction (When FS-533 is installed)
C1103 Alignment motor/Fr drive malfunction (When FS-533, FS-539, FS-540, or FS-540SD is installed)
C1104 Stacker plate drive motor malfunction (When FS-540 or FS-540SD is installed)
C1105 Bundle eject motor drive malfunction (When FS-539, FS-539SD, FS-540 is installed)
C1106 Stapler movement motor drive malfunction (When FS-533, FS-539,FS-540, or FS-540SD is installed)
C1109 Stapler motor drive malfunction (When FS-533, FS-539, FS-540, or FS-540SD is installed)
C1112 Stapler motor malfunction (When FS-539SD or FS-540SD is installed
C1113 Stopper drive motor malfunction (When FS-539SD or FS-540SD is installed)
C1114 Alignment motor drive malfunction (When FS-539SD or FS-540SD is installed)
C1115 Center fold knife motor malfunction (When FS-539SD or FS-540SD is installed)
C1124 Tray lift motor/Lw drive malfunction (When FS-540+PI-507 or FS-540SD+PI-507 is installed)
C1125 Tray lift motor/Up drive malfunction (When FS-540+PI-507 or FS-540SD+PI-507 is installed)
C1127 Punch oscillating motor malfunction (When FS-540+PK-526 or FS-540SD+PK-526 is installed)
C1130 ZU transport motor drive malfunction (When FS-540+ZU-609 or FS-540SD+ZU-609 is installed)
C1131 Folding guide motor drive malfunction (When FS-540+ZU-609 or FS-540SD+ZU-609 is installed)
C1132 Punch motor drive malfunction (When FS-533+PK-519 is installed)
C1140 Alignment motor/Rr drive malfunction (When FS-533, FS-539, FS-540, or FS-540SD is installed)
C1141 FNS paddle motor drive malfunction (When FS-539, FS-539SD, FS-540 is installed)
C1142 Paddle up/down motor drive malfunction (When FS-540 or FS-540SD is installed)
C1143 Arm drive motor drive malfunction (When FS-540 or FS-540SD is installed)
C1144 Pre-eject drive motor drive malfunction (When FS-539,FS-540, or FS-540SD is installed)
C1145 Trailing edge stopper motor drive malfunction (When FS-539,FS-540, or FS-540SD is installed)
C1146 Trail edge stopper motor/Rr drive malfunction (When FS-540 orFS-540SD is installed)
C1152 Paper transport belt motor malfunction (When FS-540SD is installed)
C1156 SD paddle motor malfunction (When FS-539SD or FS-540SD is installed)
C1182 Tray shift motor drive malfunction (When JS-508 is installed)
C1184 Paper delivery control motor drive malfunction (When FS-539, FS-540, or FS-540SD is installed)
C1195 Paper discharge control motor malfunction (When FS-539SD or FS-540SD is installed)
C1196 Center fold guide motor malfunction (When FS-539SD or FS-540SD is installed)
C1197 Tri-folding guide motor malfunction (When FS-539SD or FS-540SD is installed)
C11A1 Exit roller pressure/ retraction drive malfunction (When FS-533 isinstalled)
C11A2 Receiving roller retraction motor drive malfunction (When FS-539, FS-540, or FS-540SD is installed)
C11C5 Paper size detect board malfunction (When FS-540+PK-526 or FS-540SD+PK-526 is installed)
C11E1 Paper exit switching drive malfunction (When FS-539, FS-539SD, FS-540,or FS-540SD is installed)
C11E2 Paper exit switching (JS) drive malfunction (When FS-540 or FS-540SD isinstalled)
C1402 FS nonvolatile memory error (When FS-533 is installed)
C1403 PK flash ROM error (When FS-540+PK-526 or FS-540SD+PK-526 is installed)
C1404 PI flash ROM error (When FS-540+PI-507 or FS-540SD+PI-507 is installed)
C2152 Transfer belt fault at initial position return
C2153 Transfer belt spacing fault at K pressure switching
C2154 Transfer belt contact fault at all pressure switching
C2155 Transfer belt contact fault after K pressure established
C2156 Transfer belt spacing fault after all pressure established
C2204 Waste toner transport motor failure to turn
C2253 PC motor failure to turn
C2254 PC motor turning at abnormal timing
C2255 Developing motor failure to turn
C2256 Developing motor turning at abnormal timing
C2350 Toner suction fan failure to turn
C2355 Transfer belt cleaner cooling fan failure to turn
C2357 DV cooling fan failure to turn
C2411 Developing unit/C new article release
C2412 Developing unit/M new article release
C2413 Developing unit/Y new article release
C2414 Developing unit/K new article release
C2551 Abnormally low toner density detected cyan TCR sensor
C2552 Abnormally high toner density detected cyan TCR sensor
C2553 Abnormally low toner density detected magenta TCR sensor
C2554 Abnormally high toner density detected magenta TCR sensor
C2555 Abnormally low toner density detected yellow TCR sensor
C2556 Abnormally high toner density detected yellow TCR sensor
C2557 Abnormally low toner density detected black TCR sensor
C2558 Abnormally high toner density detected black TCR sensor
C2559 Cyan TCR sensor adjustment failure
C255A Magenta TCR sensor adjustment failure
C255B Yellow TCR sensor adjustment failure
C255C Black TCR sensor adjustment failure
C2561 Cyan TCR sensor failure
C2562 Magenta TCR sensor failure
C2563 Yellow TCR sensor failure
C2564 Black TCR sensor failure
C2650 Main backup media access error
C2A11 Drum unit/C new release failure
C2A12 Drum unit/M new release failure
C2A13 Drum unit/Y new release failure
C2A14 Drum unit/K new release failure
C2A21 Toner cartridge/C new release failure
C2A22 Toner cartridge/M new release failure
C2A23 Toner cartridge/Y new release failure
C2A24 Toner cartridge/K new release failure
C3101 Pressure roller pressure failure
C3103 Pressure roller release failure
C3104 Fusing shutter failure
C3201 Fusing motor failure to turn
C3202 Fusing motor turning at abnormal timing
C3203 Fusing motor torque failure
C3302 Paper cooling fan failure to turn
C3306 Fusing edge cooling fan/Fr failure to fr turn
C3307 Fusing edge cooling fan/Rr failure to fr turn
C3425 Fusing warm-up trouble
C3722 Fusing abnormally high temperature detection (Edge of the heating roller)
C3725 Fusing abnormally high temperature detection (Main of the heating roller)
C3726 Fusing abnormally high temperature detection (Center of the heating roller)
C3737 Fusing abnormally high temperature detection hard protector (Center of the heating roller)
C3825 Fusing abnormally low temperature detection (Main of the heating roller)
C3826 Fusing abnormally low temperature detection (Center of the heating roller)
C3922 Fusing sensor wire breaks detection (Edge of the heating roller)
C3925 Fusing sensor wire breaks detection (Main of the heating roller)
C3926 Fusing sensor wire breaks detection (Center of the heating roller)
C392B Fusing sensor wire breaks detection (difference of temperature)
C40A2 Mechanical controller PF communication data error
C40A3 Mechanical controller PF transmission timeout
C40A4 Mechanical controller PF communication pulse error
C40A5 QSPI communication clock switching error
C40A6 Mechanical controller ASIC communication error
C40C3 CTL PF transmission timeout 1
C40C5 CTL PF transmission timeout 2
C4101 Polygon motor rotation trouble
C4501 Laser malfunction
C5102 Transport motor failure to turn
C5103 Transport motor turning at abnormal timing
C5351 PH/power supply cooling fan failure to turn
C5355 Toner cartridge cooling fan failure to turn
C5358 HaCS power supply cooling fan failure to turn
C5360 Clean unit fan failure to turn (When CU-102 is installed)
C5361 UFP scavenging fan/Fr failure to turn
C5362 UFP scavenging fan/Rr failure to turn
C5363 Tacking fan failure to turn
C5370 Rear side cooling fan failure to turn C
C5372 MFP control board CPU temperature failure
C5501 AC signal abnormality
C5601 Engine control malfunction
C5603 Expansion control board communication error
C5605 Engine communication data error
C5606 Engine transmission timeout
C5610 PH LD drive communication error
C5620 Mechanical controller WDT error
C6001 DF related configuration error 1
C6002 DF related configuration error 2
C6102 Drive system home sensor malfunction
C6103 Slider over running
C6104 Back side cleaning home sensor abnormality (initial)
C6105 Back side cleaning home sensor abnormality (normal)
C6704 Image input time out
C6751 CCD clamp/gain adjustment failure
C6752 ASIC clock input error (front side)
C6753 ASIC clock input error (back side)
C6754 CIS clamp adjustment failure
C6755 CIS gain adjustment failure
C6756 CCD power-supply voltage malfunction
C6901 DSC board mount failure 1 (When SC-509 is installed)
C6902 DSC board bus check NG1-1 (When SC-509 is installed)
C6903 DSC board bus check NG1-2 (When SC-509 is installed)
C6911 DSC board mount failure 2 (When SC-509 is installed)
C6912 DSC board bus check NG2-1 (When SC-509 is installed) C Target
C6913 DSC board bus check NG2-2 (When SC-509 is installed) C Target
C6F01 Scanner sequence trouble 1 C Target
C6F02 Scanner sequence trouble 2 C Target
C6F03 Scanner sequence trouble 3 C Target
C6F04 Scanner sequence trouble 4 C Target
C6F05 Scanner sequence trouble 5 C Target
C6F06 Scanner sequence trouble 6 C Target
C6F07 Scanner sequence trouble 7 C Target
C6F08 Scanner sequence trouble 8 C Target
C6F09 Scanner sequence trouble 9 C Target
C6F0A Scanner sequence trouble 10 C Target
C6FDC Scanner sequence trouble DC B Target
C6FDD Scanner sequence trouble DD B Target
C7106 Paper exit/reverse motor failure C -
C7107 ADU transport motor/1 failure C -
C7111 Tray 1 lift-up motor failure C -
C7112 Tray 2 lift-up motor failure C -
C7131 Toner supply motor/C failure C -
C7132 Toner cartridge motor/CK failure C -
C7133 Toner supply motor/M failure C -
C7134 Toner cartridge motor/YM failure C -
C7135 Toner supply motor/Y failure C -
C7137 Toner supply motor/K failure C -
C7139 Waste toner transport motor failure C -
C7141 Fusing pressure motor failure C -
C7151 Skew correction motor/C failure C -
C7152 Skew correction motor/M failure C -
C7153 Skew correction motor/Y failure C -
C7160 Fusing shutter motor failure (bizhub C650i/C550i) B -
C7162 Tray 2 vertical transport motor failure B -
C7163 Registration motor failure (bizhub C650i) B -
C7164 ADU transport motor/2 failure B -
C7202 Tray 2 paper feed clutch failure C -
C7206 Bypass tray paper feed clutch failure C -
C720A Registration clutch failure (bizhub C550i/C450i) C -
C720B 1st transfer pressure clutch failure C -
C7241 Bypass tray lift-up solenoid failure C -
C7242 Bypass tray pick-up roller solenoid failure C -
C7243 Exit path switch solenoid failure C -
C7251 Developing solenoid failure C -
C7301 PH/power supply cooling fan failure C -
C7302 Transfer belt cleaner cooling fan failure C -
C7304 Toner cartridge cooling fan failure C -
C7305 Paper cooling fan failure C -
C7310 DV cooling fan failure B -
C7311 Fusing edge cooling fan/Rr failure (bizhub C650i/C550i) B -
C7312 Toner suction fan failure B -
C7313 UFP scavenging fan/Fr failure B -
C7314 UFP scavenging fan/Rr failure (bizhub C650i/C550i) B -
C7315 Fusing edge cooling fan/Fr failure (bizhub C650i/C550i) B -
C7317 Paper exit cooling fan failure C -
C7401 Erase LED/K failure C -
C7402 Erase LED/C failure, Erase LED/M failure, Erase LED/Y failure C -
C7501 Tray 2 upper limit sensor failure C -
C7502 Tray 1 upper limit sensor failure C -
C7601 Power line A1 error C -
C7602 Power line A2 error C -
C7603 Power line A3 error C -
C7604 Power line A4 error C -
C7605 Power line A5 error C -
C7606 Power line A6 error C -
C7607 Power line A7 error C -
C760A Power line A10 error C -
C760B Power line A11 error C -
C760C Power line A12 error C -
C760D Power line A13 error C -
C760E Power line A14 error C -
C760F Power line A15 error C -
C7610 Power line A16 error C -
C7622 Power line B2 error C -
C7623 Power line B3 error C -
C7624 Power line B4 error C -
C7631 Supply power line 1 error C -
C7633 Supply power line 3 error C -
C8103 Lift up mechanism trouble (Upward movement) B -
C8106 Lift up mechanism failure (Downward movement) B -
C8107 Glass cleaning mechanism trouble B -
C8302 DF cooling fan failure B -
C8402 Multi feed detection board failure C -
C9401 Exposure LED lighting failure B Target
C9402 Exposure LED lighting abnormally B Target
C9403 CIS LED lighting failure B Target
C9404 CIS LED lighting abnormally B Target
C9701 Front side reading device cable break detection A Target
C9702 Back side reading device cable break detection A Target
CA051 Standard controller configuration failure C -
CA052 Controller hardware error C -
CA053 Controller start failure C -
CB004 Fax board DipSw setting error C Target
CB005 No fax board is installed. Mistake in installation. Defective HW. C Target
CB006 USB connection is interrupted C Target
CB110 Program control error (instance acquisition error) C Target
CB112 Semaphore control error C Target
CB113 I/F error among tasks C Target
CB114 Message queue generation error C Target
CB115 I/F error with fax (I/F error between main body and fax) C Target
CB120 Soft error C Target
CB122 Modem-DAA initialize error C Target
CB123 Modem-DAA power save recovery error C Target
CB125 ISW failure of SubCPU C Target
CB126 Timeout of suspension process (Codec control) C Target
CB127 Timeout of suspension process (communication control) C Target
CB128 Timeout of suspension process (line control) C Target
CB129 Timeout of suspension process (modem control) C Target
CB130 I/F error with main body (fax soft error) C Target
CB131 I/F error with main body (reception frame error) C Target
CB134 I/F error with main body (sequence error) C Target
CB135 I/F error with main body C Target
CB136 ACK waiting timeout C Target
CB137 I/F error with main body (RESET reception from main body) C Target
CB139 Modem responses waiting timeout (during playing voice guidance when switching between TEL and FAX)
CB141 Fax soft error (received unexpected command) C Target
CB142 Fax soft error (received undefined command) C Target
CB143 Fax soft error (command frame length error) C Target
CB144 Fax soft error (parameter length error) C Target
CB145 Fax soft error (received undefined parameter) C Target
CB146 Fax soft error (command/response sequence error) C Target
CB150 Program control error (instance acquisition error) C Target
CB151 Job start error C Target
CB152 Doc access error C Target
CB153 Program control error (logic error) C Target
CB154 Program control error (table control error) C Target
CB158 Job generation error C Target
CB160 Program control error (instance acquisition error) C Target
CB162 Program control error (interface error) C Target
CB163 Program control error (sequence error) C Target
CB165 Program control error (table control error) C Target
CB167 Sending image access error (image acquisition error) C Target
CB168 Receiving image access error (image storage error) C Target
CB169 Sending image access error (image deletion error) C Target
CB170 Program control error (table control error) C Target
CB171 Program control error (instance acquisition error) C Target
CB173 Program control error (interface error) C Target
CB176 Unable to secure domain for header (TTI) image generation C Target
CB177 Header (TTI) image generation error C Target
CB185 Receiving data size logic error (Receiving data are not multiples of dotline)
CB186 Unable to secure domain for receiving image C Target
CB187 Receiving image conversion error C Target
CB188 Program control error (table control error) C Target
CB190 USB sending error C Target
CB191 USB sending error C Target
CB192 Error retry 5 sec. T.O (No response or other errors) C Target
CB193 No response due to detach of USB C Target
CB195 Attach not detected for 1 min. after recovery from sleep when receiving C Target
CB196 Detach not detected for 1 min. after shift from sleep C Target
CB197 USB I/F error during formatting when main power switch ON C Target
CB198 Attach not detected for 1 min. after recovery from sleep at the time other than receiving
CC002 Vendor internal error C Target
CC151 ROM contents error upon startup (MSC) C Target
CC152 ROM contents error upon startup (IR) C Target
CC155 Finisher ROM error (When FS-533, FS-539, FS-539SD, FS-540, or JS-508 is installed)
CC156 DF ROM error C Target
CC159 ROM contents error upon startup (DSC1) C Target
CC15A ROM contents error upon startup (DSC2) C Target
CC15B Flash ROM error (saddle) (When FS-539SD or FS-540SD is installed) C -
CC15C Engine Flash ROM writing error C -
CC163 ROM contents error (PRT) C -
CC164 ROM contents error (MSC) C Target
CC170 Dynamic link error during starting (AP0) C Target
CC171 Dynamic link error during starting (AP1) C Target
CC172 Dynamic link error during starting (AP2) C Target
CC173 Dynamic link error during starting (AP3) C Target
CC174 Dynamic link error during starting (AP4) C Target
CC180 Dynamic link error during starting (LDR) C Target
CC181 Dynamic link error during starting (IBR) C Target
CC182 Dynamic link error during starting (IID) C Target
CC183 Dynamic link error during starting (IPF) C Target
CC184 Dynamic link error during starting (IMY) C Target
CC185 Dynamic link error during starting (SPF) C Target
CC186 Dynamic link error during starting (OAP) C Target
CC190 Outline font load error C Target
CC191 Setting parameter load error (LDR) C Target
CC211 Authentication device general error C Target
CC212 User validation error C Target
CC213 User registration error/Card information setting error C Target
CC214 User information deletion error C Target
CC216 Acquisition failure of the number of trials/Initialize error of number of authentication
CC301 Authentication customize data error B Target
CC302 Authentication customize data version mismatch error B Target
CCC00 Public user account track information error B -
CD002 JOB RAM save error C Target
CD004 Storage access error (connection failure) C Target
CD00F Storage data transfer error C Target
CD010 Storage unformat C Target
CD011 Storage out of specifications mounted C Target
CD012 Mount error due to storage being unformatted C Target
CD020 Storage verify error C Target
CD030 Storage management information reading error C Target
CD041 Storage command execution error C Target
CD042 C Target
CD043 C Target
CD044 C Target
CD045 C Target
CD046 C Target
CD047 Storage SCSI library error C Target
CD048 C Target
CD049 C Target
CD04A C Target
CD04B C Target
CD050 Storage recovery timeout C Target
CD072 Second-hand SSD or second-hand CPU board installed C Target
CD073 Storage type mismatch C Target
CD110 Wireless LAN destination initialization error C Target
CD201 File memory mounting error C Target
CD202 Memory capacity discrepancy C Target
CD203 Memory capacity discrepancy 2 C Target
CD211 PCI-SDRAM DMA operation failure C Target
CD212 Compression/extraction timeout detection C Target
CD241 Encryption ASIC setting error C Target
CD242 Encryption ASIC mounting error C Target
CD252 No relay circuit boards for IC-420 mounting at IC-420 mount setting C Target
CD261 USB hub board failure C Target
CD262 Extension network adapter installation error C Target
CD2D1 VLAN setting configuration error B -
CD3## Nonvolatile data error C Target
CD313 TPM key data error C Target
CD38E Nonvolatile data save error (SPI-Flash) C Target
CD390 Nonvolatile data checksum error C Target
CD391 Nonvolatile data save error (Storage) - Target
CD392 Nonvolatile data save error (EEPROM) C Target
CD3B1 DB server startup failure C Target
CD3B3 DB access failure C Target
CD3B4 No DB definition file C Target
CD3B5 DB definition file error C Target
CD3C0 New board detection C Target
CD401 NACK command incorrect C Target
CD402 ACK command incorrect C Target
CD403 Checksum error C Target
CD404 Receiving packet incorrect C Target
CD405 Receiving packet analysis error C Target
CD406 ACK receiving timeout C Target
CD407 Retransmission timeout C Target
CD411 Touch panel board error C Target
CD412 Touch panel type mismatch C Target
CD413 Electrostatic touch panel operation mode error C Target
CD601 Trouble related to security - -
CD602
CD603
CD701 Mechanical controller flash ROM writing error C -
CD702 Mechanical controller flash ROM device error C -
CD703 FW download communication fault C -
CD704 Finisher Flash ROM device error (When FS-533, FS-539, FS-540, FS-540SD, or JS-508 is installed)
CDC## Trouble related to security - -
CDF50 ASIC image version failure C Target
CDF51 ASIC image version failure (back side) (When DF is installed) C Target
CDF70 ASIC image access failure C Target
CDF71 ASIC image access failure (back side) (When DF is installed) C Target
CDFA0 ASIC image error C Target
CDFA1 ASIC image error (back side) (When DF is installed) C Target
CE001 Abnormal message queue C Target
CE002 Message and method parameter failure C Target
CE003 Task error C Target
CE004 Event error C Target
CE005 Memory access error C Target
CE006 Header access error C Target
CE007 DIMM initialize error C Target
CE009 Memory resource shortage error C Target
CE012 Failed to receive the entropy from Haveged C Target
CE013 Virus scan engine startup failure (8 GB storage) C Target
CE014 Virus scan engine startup failure (storage error) C Target
CE015 Secret information issue error C Target
CE101 Browser finish detected C Target
CE201 Transmission operation log storage fault C Target
CE202 PDL interpreter error C Target
CE203 Unrecoverable error C Target
CE204 SIP / T.38 library loading failure C Target
CE301 Referring incorrect memory C Target
CE302 Incorrect command C Target
CE303 Finished due to error inside Qt library C Target
CE304 Finished due to error outside Qt library C Target
CE305 Program forced to stop C Target
CE401 Shared memory connection timeout C Target
CED01 The authentication application information does not exist in the storage inthe enhanced server authentication state.
CEEE1 CPU board (MSC) malfunction C Target
CEEE2 Scanner section malfunction A Target
CEEE3 Base board (ENG) malfunction A Target
CF### Trouble code (CF###) is referred to as abort code.For details of abort code, refer to “ABORT CODE”.
San Diego Copier Repair
Copyright San Diego Copier Repair. All rights reserved.